Service

TPMS: Hyundai Elantra, Elantra Coupe and Elantra Touring

Information provided by Mitchell 1
Posted on March 6, 2018
Figure 1: Registering the tire pressure sensor (one of two).
Figure 1: Registering the tire pressure sensor (one of two).

SUBJECT VEHICLES: 2011-2017 Hyundai Elantra, 2014 Elantra Coupe and 2009-2012 Elantra Touring.

RELEARN PROCEDURE? Yes.

SPECIAL TOOLS NEEDED? Yes, a Hyundai GDS (Global Diagnostic System) with the TPMS module.

The tire pressure monitoring system (TPMS) of the 2011-2017 Hyundai Elantra, 2014 Elantra Coupe and 2009-2012 Elantra Touring monitors the air pressure in the four road tires with wheel-mounted tire pressure sensors. To do this, the system uses a receiver, four radio frequency (RF) tire pressure sensors, two warning indicators on the instrument cluster, and a data circuit to perform system functions.

When tire pressure is below the allowed threshold or a rapid leak is detected, the low pressure warning light on the instrument cluster will be illuminated. If the system detects a receiver or sensor fault, or if it detects a fault that is external to the receiver or sensor, the TPMS warning indicator will be illuminated. If the fault is considered “critical,” the light will stay on throughout the entire ignition cycle.

The tire pressure sensor operates in two modes: stationary/rolling mode and sleep mode. In the stationary/rolling mode, the sensor will measure pressure and temperature every four seconds, and measure acceleration every 60 seconds. In sleep mode, the sensor enters a low current consumption state where no measurements are made in order to conserve battery power. All sensors are in this state when new. The sensor will not transmit unless requested to do so by the initiate command or when the vehicle accelerates to 20 mph (32 km/h).

Tire pressure monitor warning indicators

When the low tire pressure warning light comes on the air pressure of all tires needs checked and adjusted to the specified cold pressure listed on the vehicle certification label (found on the driver’s door or door pillar). If the tire is damaged, repair as necessary. Ensure the warning light goes off (this may take up to four minutes if the tire is not rapidly re-inflated). If the warning light stays on, recheck tire pressure. If tire pressure is OK, turn the wheel a quarter turn and wait another four minutes (the sensor may be in an RF null). If the warning light is still on or if the TPMS warning indicator is lit, there is a malfunction in the TPMS.

Reset procedures

NOTE: If the tire pressure sensor is replaced, it will need to be initiated. The TPMS is not affected by wheel and tire rotation. When the low tire pressure warning light comes on, check the air pressure of all tires and adjust to the specified cold pressure listed on vehicle certification label (found on driver’s door or door pillar). Ensure the warning light goes off (this may take up to four minutes if the tire is not rapidly re-inflated).

Tire pressure sensor initiation (automatic)

  • Auto-locate/learn takes place only once per ignition cycle. On successful completion, four road wheel sensor IDs, together with their respective road wheel positions, are latched into memory for monitoring.
  • Until Auto-Learn completes, previously learned sensors (together with their respective locations) are monitored for under-inflation / leak warnings.
  • Auto-location / learning only functions when speed is more than 15 mph (20 kph).
  • It takes less than 10 minutes at 15 mph (20 kph).

Tire pressure sensor initiation (manual)

NOTE: In the following procedure, a Hyundai GDS (Global Diagnostic System) with the TPMS module must be used. NOTE: When four sensors have been learned as road wheels, it is not possible to learn new road wheel sensors on the same ignition cycle.

1) Condition – Ignition ON and Engine OFF

2) Hold the TPMS module within 3 inches (76 mm) of the sensor valve, read each tire pressure sensor ID in the following order: front left, front right, rear left, then rear right.

3) Press the ENTER button as each tire is illuminated on the screen.

4) Press the WRITE button after reading all of the sensor IDs.

Figure 2: Registering the tire pressure sensor (two of two — see the previous page for step one).
Figure 2: Registering the tire pressure sensor (two of two — see the previous page for step one).
5) Connect GDS to Data Link Connector (DLC) located under the left side of the instrument panel. Register the four sensor IDs to the receiver (see Figures 1 and 2).

NOTE: The TPMS receiver will complete the learn procedure of the new sensor after the vehicle is driven up to 20 minutes at speeds over 20 mph (32 km/h).

NOTE: For the system to correctly monitor the tires for under-inflation, there should be a total of exactly four sensors, one on each of the four road wheel positions. There should be no other sensors in the vehicle since this could cause the system to monitor the wrong sensors or fail to lean a new sensor.

6) Modify any sensor ID and press the [OK] button.

Demounting/mounting procedures

CAUTION: The tire should be demounted from the wheel using the tire changer manufacturer’s instructions. Use the following information to avoid damage during the demounting/mounting procedures. Ensure that the wheel to be fitted is designed for the sensor mount. There should normally be a mark to indicate this.

NOTE: If the tire pressure sensor is replaced, it will need to be initiated. See “Reset procedures.” The TPMS is not affected by wheel and tire rotation.

NOTE: Tire pressure is also dependent on temperature of the tire. For every 18 degrees Fahrenheit (10 degrees Celsius) increase in tire temperature, tire pressure increases about 1.5 psi (10 kPa). Tire pressure should only be adjusted when tires are cold (about the same as ambient air temperature).CAUTION: Do not use puncture repair fluid, as this can cause sensor pressure port to block and an incorrect warning to occur.

Removal

1) Remove the wheel and tire assembly.

CAUTION: Avoid tire/tool contact with the valve while demounting the tire.

2) Deflate the tire and remove the balance weights. The tire bead should be broken about 180 degrees from the valve side of the wheel. The bead breaker should not be set too deep. Demount should end near the valve.

CAUTION: The valve nut should not be re-used.

3) While handling the sensor with care, remove the valve nut.

4) Discard the valve stem assembly.

Installation

CAUTION: Avoid bringing tire pressure sensor in contact with lubricant. Always handle the tire pressure sensor carefully.

1) Assemble the valve to the sensor, making sure the hex nut is in contact with the metal insert in the sensor body (see Figure 3).

Figure 3: Installing the valve to the sensor.
Figure 3: Installing the valve to the sensor.
2) Tighten the 7 mm nut with a nut driver to the required torque. See “Torque specifications.

3) Ensure that the valve hole and mating face of the wheel are clean. Mount assembly to the wheel using a standard valve stem puller tool.

4) Lubricate the tire bead (not the rim). Do not use excessive lubrication.

5) Start tire mounting at about the 5 o’clock position from the valve. Move the mounting tool away from the valve. Avoid tire/tool contact with the valve. Finish with the mounting tool near the valve.

6) Adjust inflation pressure of all the wheels. Install the valve cap.

7) If installing a new sensor, initiate the tire pressure sensor. ■

Torque specifications

Component Ft.-lbs. (N.m)

Wheel nut 65-79.6 (88-108)

In.-lbs. (N.m)

Tire pressure sensor valve nut 35 (4)

Information for this column comes from Mitchell 1’s “Tire Pressure Monitoring Systems Guide” for domestic and import vehicles. Headquartered in Poway, Calif., Mitchell 1 has provided quality repair information solutions to the automotive industry for more than 80 years. For more information, visit www.mitchell1.com. For archived TPMS articles, visit www.moderntiredealer.com.

Artwork courtesy of Hyundai Motor Co.

To read more TPMS columns, click:

Volkswagen Passat 2012-2017

2017 Nissan Rogue and Rogue Select

Kia Sorento 2011-2017

Honda Pilot and Ridgeline, 2005-2016

Related Topics: Hyundai Elantra Coupe, Hyundai Elantra Hyundai, Hyundai Elantra Touring, Tire pressure monitoring systems, TPMS

Comments ( 0 )
More Stories
The ADS 625 (pictured) and ADS 325 scan tools are part of Bosch's new Automotive Diagnostic Solutions line.
Product

Bosch Introduces Two Diagnostic Scan Tools

The new ADS 325 and ADS 625 scan tools from Bosch Automotive Service Solutions feature full diagnostic capabilities including system scans, data stream, special tests, bi-directional controls, and repair information.

News

Versatile Credit Adds EasyPay Finance Option

Versatile Credit Inc. has added the EasyPay Finance option to its list of platform offerings. The "second look" option focuses on offering financing solutions to the automotive market.

Article

Unit Sales Volumes Were Up Nearly 2%

Our recent discussions with dealers leave us with a view that sell-out trends improved in May versus the prior year’s period, re-accelerating from year-over-year contractions early in the year. While always somewhat subjective, we note commentary from installers was at the highest level since October 2017. From a volume standpoint, surveyed dealers reported they saw unit sales volumes up nearly 2% relative to the previous year’s period.

News

New Tire Pros Ad Campaign Costs $1 Million

American Tire Distributors Inc. (ATD) has launched a $1 million ad campaign highlighting the work of its Tire Pros franchisees. The message is hassle-free customer service.

ATEQ TPMS Tools and Jeff Buckley, owner of My Father’s Shop, are collaborating on Facebook to give away two TPMS tools to high schools, technical centers or colleges during their “Back to School” giveaway.
News

Ateq Collaborates with Texas Shop Owner to Give Away TPMS Tools

Ateq TPMS Tools and Jeff Buckley, owner of My Father’s Shop, are collaborating on Facebook to give away two tire pressure monitoring system (TPMS) tools to high schools, technical centers or colleges during their “Back to School” giveaway. Ateq and Buckley will each donate a VT36 TPMS tool to two winners.

Be the First to Know

Get the latest news and most popular articles from MTD delivered straight to your inbox. Stay on top of the tire industry and don't miss a thing!